The Most Easiest of Reading and Writing Mercedes W166 edc17cp46
When many users got Ktag OBD master, some of them are confused about its function, and some don’t how to use it, some even don’t know whether it can make best use of Mercedes ML w166 edc17cp46 with KTAG clone and trasdata software, well, i will tell you the details step by step.
Best Fuctions:
1. Online Version Kess V2 Firmware V5.017 support online service by interent connection
2. 100% No Tokens Need for all vehicles, no tokens reset button, you can use Kess V5.017 for lifetime
3. Kess V2 Ksuite V2.23 Firmware V5.017 cover all major brands and protocols including Line, KAN, EDC17 and MED17 and for Ford J1850.
4. KESS V2 V5.017 can support cars/trucks/tractors/bikes! KESS V2 supports vehicles accroding to engine. So V5.017 KESS V2 can support new vehicles!
6. Kess V2 V5.017can read and write ECU via OBD2 port directly, no need to disassemble ECU from the car, easy to use.
Yes, work fine
How to read Mercedes bosch edc17cp46 with Ktag?
When you read with Ktag, after full read (saved) Don’t turn off power supply and press patch … and Ktag will automatically write Patched files back to ECU. and the same time Ktag will save Patched file as well in you saved folder where you save this file. you can use this saved patched file to flash with Kess V2(OBD).
ECU: Mercedes ML w166 bosch edc17cp46
Both Fgtech Galletto v54 clone and Ktag OK for Mercedes edc17cp46?
read and write edc17cp46 2013 and unlock tprot with Galletto v54eu from vipprogrammer:
90% of EDC17cp46 can be read/write in Boot mode with Galleto V54 ! after you have read and save just bypass TPROT in file !
Actually, no one Fgtech clone work on this ecu, missing password. So you can not read ecu with Fgtech ! Use Transdata or KESS KTAG with GPT optione !
Step 1: Read password
Please connect the Tricore cable as shown in the picture below
Connect described the R3 and R4 pin with the special adapter as shown in the picture
(expand your TriCore cable with R3 and R4)
Do not connect the 1-kOhm boot pin
Read password file
Save the password file
Step 2: Read or write data of control unit
Please connect the Tricore cable as shown in the picture below
Connect the boot pin with specified boot resistance (1-kOhm)
Connect the boot pin with resistance 1-kOhm to ground/GND
Continue with the respective action, reading and writing
It will open a new window in which you can select File password
Select your password files you saved previously, and press Open
Begin to Read/Write
Explanation of the car terminals:
Klemme (15) = +12Volt switch power/Geschaltetes Plus
Klemme (30) = +12Volt permanent Power/dauer Plus
Klemme (31) = GND Ground/Masse – GND Ground/Masse
K-Line = K-Line ISO 9141 On Board Diagnostics vehicle network interface
CAN High = CAN High Controller Area Network
CAN Low = CAN Low Controller Area Network – CAN Low Controller Area Network
Ktag v7.020 mercedes edc17cp46 wiring diagram:
Control unit location:
The new TriCore password function is supported only by Dual 1 and Dual 2.
Cautions:
To use this protocol of communication you have to remove and open the KTAG ECU Chip Tuning ProgrammerIt is a risky operation, to be done with great care and caution to avoid damaging the ECU beyond repair.
After opening the ECU and before proceeding with reading and/or programming, you are strongly advised to reconnect the unit to the vehicle and start the engine, to make sure it still works.
To use this protocol you also need to connect to the ECU connector through a cable, and solder one or more wires to the programming pads.
Incorrect or poorly made connections and solderings may damage the ECU, often beyond repair.
Under no circumstances we shall be liable for any damage caused to the ECU during the opening, due to connections and soldering that do not comply with the instructions provided in this manual.
BY USING THIS PROTOCOL, YOU CONFIRM YOUR FULL AND UNCONDITIONAL ACCEPTANCE OF THIS TERMS AND CONDITIONS, YOU RELIEVE US FROM ANY RESPONSABILITY AND RENOUNCE TO ALL RIGHTS TO CLAIM ANY COMPENSATION.
There are more update news on our website: vipprogrammer.com, welcome your visit to get more news in time.
